It is no secret that buying new car batteries is an expensive venture. Depending on quality, you will always be required to part with $100 to $200 dollars for a brand new version of the same. As a result many people have developed the critical technique of re-awakening the ones that had been presumed dead and useless. For those in Dallas Texas, this is no news as there are many used car batteries Dallas TX dealers who earn their livelihood by selling these products. You might want to refurbish one of your own without visiting these merchants, so what does it actually take?
The first procedure entails assembling of all the necessary implement and tools that might be required. Neoprene rubber gloves is just but one of them and is essential in ensuring that your hands are kept of possible corrosion as the acid is not that friendly. Secondly, you require a heavy shop apron to guard the rest of your body against potential harm resulting from accidental acid spillage. You might also require safety glasses for the eyes as there are numerous poisonous gasses that are emitted during the process. Magnesium sulfate, turkey baster and distilled water are also required for direct usage in the procedure.
To start with, boil half a gallon of distilled water followed by the addition of magnesium sulfate. Stir this mixture carefully making sure that you take necessary precautions. Set this mixture aside and go ahead to scrub all the corrosion from the terminal and cables; ready for the subsequent procedures.
Properly handling the device, carefully remove the battery cell covers with the help of a screw driver. This is achieved by simply prying them off. This is followed by thorough cleaning of the areas next to the open holes using a damp piece of clothing. Using the funnel, slowly add the mixture to each cell making sure that the visible lead plates are covered.
This is followed by having all the covers that were initially taken out carefully returned. Thereafter, vigorously shake the battery to ensure that all surfaces that were to be coated are done so appropriately. This should be done more than ten times to produce satisfactory results.
Thereafter, have the battery connected to a continuous power source via the terminals. This ought to take place for at least twenty four hours to ensure that the battery is fully ready for usage. However, this might be repeated if the condition or type battery that is being refurbished demands so.
It is of essence to take note that the charging process need not be continuous over the entire period. Studies have shown that it is advisable to constantly discharge the battery between cycles to increase its subsequent performance. Alternatively, you can have it reconnected to the terminal of a car with the headlights on. When the lights begin to dim, remove the battery and once more charge as prior explained.
Taking precautions during the procedure is never an option as no one would like to lose a part of his body or even the life in the course of the process. Just ensure that the battery does not overcharge to avoid possible explosion and then use other materials that are not likely to react with the battery acid.
The first procedure entails assembling of all the necessary implement and tools that might be required. Neoprene rubber gloves is just but one of them and is essential in ensuring that your hands are kept of possible corrosion as the acid is not that friendly. Secondly, you require a heavy shop apron to guard the rest of your body against potential harm resulting from accidental acid spillage. You might also require safety glasses for the eyes as there are numerous poisonous gasses that are emitted during the process. Magnesium sulfate, turkey baster and distilled water are also required for direct usage in the procedure.
To start with, boil half a gallon of distilled water followed by the addition of magnesium sulfate. Stir this mixture carefully making sure that you take necessary precautions. Set this mixture aside and go ahead to scrub all the corrosion from the terminal and cables; ready for the subsequent procedures.
Properly handling the device, carefully remove the battery cell covers with the help of a screw driver. This is achieved by simply prying them off. This is followed by thorough cleaning of the areas next to the open holes using a damp piece of clothing. Using the funnel, slowly add the mixture to each cell making sure that the visible lead plates are covered.
This is followed by having all the covers that were initially taken out carefully returned. Thereafter, vigorously shake the battery to ensure that all surfaces that were to be coated are done so appropriately. This should be done more than ten times to produce satisfactory results.
Thereafter, have the battery connected to a continuous power source via the terminals. This ought to take place for at least twenty four hours to ensure that the battery is fully ready for usage. However, this might be repeated if the condition or type battery that is being refurbished demands so.
It is of essence to take note that the charging process need not be continuous over the entire period. Studies have shown that it is advisable to constantly discharge the battery between cycles to increase its subsequent performance. Alternatively, you can have it reconnected to the terminal of a car with the headlights on. When the lights begin to dim, remove the battery and once more charge as prior explained.
Taking precautions during the procedure is never an option as no one would like to lose a part of his body or even the life in the course of the process. Just ensure that the battery does not overcharge to avoid possible explosion and then use other materials that are not likely to react with the battery acid.
0 comments:
Post a Comment