The fumes regulator system that communicates with your engines computer is called an oxygen sensor. It makes the rate at which your engine burns fuel become faster by monitoring the ratio of the air and fuel in your cars engine. It will control fuel usage by looking at the ratio of air and fuel present to see whether it is optimum. This results in your engine running as efficiently as possible and also makes its produce less emissions. All this is done by ensuring that your engine uses just the right amount of fuel to run the car. This makes you understand why you should always aim for O2 sensor recycling.
The first thing you have to check is that all the shielding gears are in place for this process. You will need gloves that resist heat and safety glasses for your face. You can use a face mask in place of glasses. You can now proceed to remove the sensor from your car.
You can be able to peep in and see the dense carbon that has coated the reader. Next, put on the heat gloves and turn on a blowtorch to an optimum heat level. If you do not use the gloves you will only harm yourself.
By use of tongs, you will then hold the oxygen reader in your hand and direct its opening to the flame of fire produced by a blowtorch until it becomes red. The aim of heating up the opening is to get rid of coagulated carbon in the device.
After you are sure all the carbon has been rid of, turn off the blowtorch then allow the reader to cool off. A bit of water can be used on the opening to speed up the cooling process though you must be extremely careful not to dip the whole thing in water.
After this is done, you can spray the tip of the reader with compressed air. The compressed air will help to remove any soot that might have built up in the device. If you notice that there still seems to be hardened soot left that you cannot remove manually, then you should repeat the procedure again until the device is soot free.
You should then return it back to your exhaust and test it. The light in the engine should not come on if the process was successful. If it does you will have to discard the current one you have and get a brand new one.
You should never attempt to operate a blowtorch if you are not experienced in its use. By going to a garage or an electrical hardware, you can avoid damaging the sensor or burning yourself by having an experienced and qualified electrician do the procedure for you.
You might realize there is no hope of reusing your engines oxygen sensor so you are advised to have its parts recycled. By going through your local directory, you will find qualified recyclers to handle O2 sensor recycling.
The first thing you have to check is that all the shielding gears are in place for this process. You will need gloves that resist heat and safety glasses for your face. You can use a face mask in place of glasses. You can now proceed to remove the sensor from your car.
You can be able to peep in and see the dense carbon that has coated the reader. Next, put on the heat gloves and turn on a blowtorch to an optimum heat level. If you do not use the gloves you will only harm yourself.
By use of tongs, you will then hold the oxygen reader in your hand and direct its opening to the flame of fire produced by a blowtorch until it becomes red. The aim of heating up the opening is to get rid of coagulated carbon in the device.
After you are sure all the carbon has been rid of, turn off the blowtorch then allow the reader to cool off. A bit of water can be used on the opening to speed up the cooling process though you must be extremely careful not to dip the whole thing in water.
After this is done, you can spray the tip of the reader with compressed air. The compressed air will help to remove any soot that might have built up in the device. If you notice that there still seems to be hardened soot left that you cannot remove manually, then you should repeat the procedure again until the device is soot free.
You should then return it back to your exhaust and test it. The light in the engine should not come on if the process was successful. If it does you will have to discard the current one you have and get a brand new one.
You should never attempt to operate a blowtorch if you are not experienced in its use. By going to a garage or an electrical hardware, you can avoid damaging the sensor or burning yourself by having an experienced and qualified electrician do the procedure for you.
You might realize there is no hope of reusing your engines oxygen sensor so you are advised to have its parts recycled. By going through your local directory, you will find qualified recyclers to handle O2 sensor recycling.
0 comments:
Post a Comment